热线电话
0531-69951198
网站首页
关于精拓
产品展厅
新闻中心
原理选型
客户案例
在线留言
联系我们
网站公告:

新闻中心

济南精拓流体设备有限公司

电话:0531-69951198

邮箱:jingtuolt@163.com

传真:0531-69951198

地址:济南市历城区祝甸北路2号院

网址:http://www.sdjingtuo.com

常见问题

当前位置:首页 - 新闻中心 - 常见问题初次使用气液增压泵应该注

初次使用气液增压泵应该注意这些

发布时间:2023-02-22 10:55:53   发布人:http://www.sdjingtuo.com
对使用过气液增压泵的用户来说是没什么的,但是对初次使用者来说操作不当会导致被检测件因为压力过高而损坏,下面小编就给大家总结下初次使用要注意那些细节。
It is nothing for users who have used gas-liquid booster pump, but for initial users, improper operation will lead to damage of the tested parts due to high pressure. The following is a summary of the details to be paid attention to in initial use.
1.初次使用要确保气液增压泵是按厂方要求连接,不要用低于气液增压泵高使用压力的配件如:高压管路,卡套接头,高压开关等。
1. In the initial use, ensure that the gas-liquid booster pump is connected according to the requirements of the manufacturer. Do not use accessories that are lower than the high service pressure of the gas-liquid booster pump, such as high-pressure pipes, ferrule joints, high-pressure switches, etc.
2.在使用合适的配件下按使用要求以此连接好,再检查是否有泄露(液压和气压不同稍微泄露会导致压力浮动较大,再次增压会形成脉冲对产品精密部件有影响)。
2. After using the appropriate accessories, connect them according to the use requirements, and then check whether there is leakage (slight leakage due to different hydraulic pressure and air pressure will lead to large pressure fluctuation, and re-pressurization will cause pulse to affect the precision parts of the product).
3.在满足上述条件后再检查驱动气源是否满足使用要求,被增压的介质是否纯洁和连接好
3. After meeting the above conditions, check whether the driving air source meets the use requirements, and whether the pressurized medium is clean and connected
气液增压泵
4.完成以上步奏后打开驱动气源,调节二连体上的压力调节阀,从压力0往高处调节所使用压力,等气液增压泵高压出口有液体排出时证明增压缸内空气完全排出,切断驱动气源,连接被检测件再打开气源。
4. After completing the above steps, open the driving air source, adjust the pressure regulating valve on the duplex, and adjust it from 0 to the used pressure. When there is liquid discharged from the high-pressure outlet of the gas-liquid booster pump, it is proved that the air in the booster cylinder is completely discharged, cut off the driving air source, connect the tested part, and then open the air source.
如果检测在长时间内承压能力就不用切断气源,检测密封性2种办法:1,切断气源看压降2,保持气源畅通看渗漏。
If the pressure bearing capacity is tested for a long time, it is not necessary to cut off the gas source. There are two ways to test the tightness: 1. Cut off the gas source to see the pressure drop; 2. Keep the gas source unblocked to see the leakage.
今天关于气液增压泵的知识就介绍到这了,您还有什么不了解的请访问我们的官网,也可直接电话联系我们http://www.sdjingtuo.com
Today's knowledge about gas-liquid booster pump is introduced here. If you don't know anything else, please visit our official website or call us directly http://www.sdjingtuo.com !
新闻: