气体增压泵是以压缩空气为动力源的一种活塞式增压泵，当进气时增压气控阀的阀芯往复切换工作，控制增压泵活塞以极快的速度作往复动作，随着输出压力的增高，活塞的往复速度减慢直停止，此时，增压泵输出的压力恒定，能量消耗低，各部件停止工作；无/何种原因造成保压回路压力下降，增压泵将自动启动，补充泄露压力，保持回路压力恒定。大驱动气压为8bar。 1-驱动空气入口；2-驱动空气管路；3-气动活塞；4-顶部撞针；5-先导阀口；6-换向阀；7-底部撞针；8-先导排气口；9-消声器；10-入口单向阀；11-出口单向阀气动气6增压泵一般用于产品气压测试、提升工厂局部气源压力等，在次使用前，须详细阅读产品相关使用说明，切勿凭感觉操作。使用时，注意以下事项等，可用的更久。 1、使用的环境粉尘不能太多，因为气动气体增压泵上的呼吸孔可能会把杂志吸入泵的腔体内6，进而可能会导致其上的密封圈机缸筒划伤等情况的发生，大大的缩减应有的使用寿命年限。 2、如有条件的，可通过加配油水分离器来达到过滤掉空气驱动气源中的杂质以及水分等，这对于延长综合使用年限都是很有帮助的。

A gas booster pump is a piston type booster pump that uses compressed air as the power source. When the air is intake, the valve core of the booster gas control valve switches back and forth, controlling the booster pump piston to perform reciprocating action at an extremely fast speed. As the output pressure increases, the reciprocating speed of the piston slows down until it stops. At this time, the output pressure of the booster pump is constant, energy consumption is low, and all components stop working; If there is no reason for the pressure drop in the pressure maintaining circuit, the booster pump will automatically start to supplement the leakage pressure and maintain a constant circuit pressure. The driving pressure is 8 bar. 1. Drive air inlet; 2- Drive air pipeline; 3- Pneumatic piston; 4-Top firing pin; 5- Pilot valve port; 6-directional valve; 7- Bottom firing pin; 8- Pilot exhaust port; 9- Silencer; 10- Inlet one-way valve; 11. The outlet one-way valve pneumatic 6 booster pump is generally used for product air pressure testing, improving local air supply pressure in the factory, etc. Before the first use, it is necessary to carefully read the relevant product instructions and not operate based on intuition. When using, pay attention to the following items, etc., for longer use. 1. The environmental dust used should not be too much, as the breathing hole on the pneumatic gas booster pump may suck the magazine into the pump chamber, which may cause scratches on the sealing ring and cylinder barrel, greatly reducing the expected service life. 2. If conditions permit, an oil-water separator can be added to filter out impurities and moisture in the air driven gas source, which is helpful for extending the comprehensive service life.

气体增压系统气体增压系统是根据客户的实际需要，将增压泵及各部件装配在管式框架内或封闭箱体内，结构紧凑，使用方便。压力表、阀、压力调节器均为面板安装。通过设定气压调节器可调节输出压力。到达设定压力时泵自动停止，压力下降时恢复工作。3－8bar普通洁净压缩空气驱动，气体工作压力可达80MPa,如果需更高压力选用双驱动头增压

The gas boosting system is based on the actual needs of customers, where the booster pump and various components are assembled in a tubular frame or enclosed box, with a compact structure and convenient use. The pressure gauge, valve, and pressure regulator are all panel mounted. The output pressure can be adjusted by setting the air pressure regulator. When the set pressure is reached, the pump automatically stops and resumes operation when the pressure drops. 3-8bar ordinary clean compressed air drive, gas working pressure can reach 80MPa, if higher pressure is required, double drive head boosting is selected

产品典型应用：

Typical application of the product:

1.用于工厂压缩空气的二次增压，氮气、氢气高压反应釜的充装，及其它需各种高压气体的场合。

1. Used for secondary pressurization of compressed air in factories, filling of high-pressure reaction vessels for nitrogen and hydrogen, and other situations that require various high-pressure gases.

2.气体辅助注塑，及其辅助注塑中的高压氮气充气

2. Gas assisted injection molding and high-pressure nitrogen inflation in assisted injection molding

3.阀门、管件，冷凝管、空调盘管的气密性测试，阀门及井口装置水中冒泡试验

3. Air tightness testing of valves, fittings, condensate pipes, and air conditioning coils, as well as water bubbling testing of valves and wellhead safety devices

4.航空航天附件维修后的静态动态测试，阀门校定

4. Static and dynamic testing of aerospace accessories after maintenance, and calibration of safety valves

5.汽车制动系统测试，通讯电缆充气设备

5. Automotive brake system testing, communication cable inflation equipment

6.飞机轮胎和液压蓄能器充氮气，高压气体系统和仪器的测试

6. Testing of aircraft tires and hydraulic accumulators filled with nitrogen, high-pressure gas systems, and instruments

7.去矿化作用，如反渗透作用及脱盐作用

7. Demineralization processes, such as reverse osmosis and desalination

8.提供压力以测验或校准天然气元件

8. Provide pressure to test or calibrate natural gas components

9.记录井下流体深度声波设备的动力，及高压气体流形态研究。

9. Record the power of downhole fluid depth acoustic equipment and study the morphology of high-pressure gas flow.

本文来自：气体增压泵更多的内容请点击：http://www.sdjingtuo.com我们将会为您提问的问题提供一个满意的服务，欢迎您的来

This article is from: Gas Booster Pump. For more information, please click on: http://www.sdjingtuo.com We will provide you with a satisfactory service for the questions you ask. Welcome to come