气体增压泵实际上我们日常并不使用，但如果您有这方面的使用计划，就需要提前来了解它的事情，下面建议您看看这些信息。
In fact, we don't use the gas booster pump in daily life, but if you have a plan for its use, you need to know about it in advance. I suggest you take a look at this information.
1、使用油水分离器。
1. Use an oil-water separator.
压缩空气作为驱动气体进入气体增压泵前须使用油水分离器去除冷凝水、油污或者杂质。
Before the compressed air enters the gas booster pump as the driving gas, the oil-water separator must be used to remove condensate, oil or impurities.
2、加装过滤器。
2. Add filter.
预增气体（氢气、氮气、氦气等）通过增压后，可能也会有水凝结出来，并且气体增压泵内也会发生磨损，因此气体增压泵的气体输入口和高压输出口都须加过滤器。
After the pre added gas (hydrogen, nitrogen, helium, etc.) is pressurized, water may also condense, and wear may also occur in the gas booster pump. Therefore, filters must be added to the gas inlet and high-pressure output of the gas booster pump.
3、如果，输出端用气设备内压力低于入口预增气压力时，设备可通过单向阀向设备内部直接充气，因此可节省充气时间。
3. If the pressure in the gas equipment at the output end is lower than the inlet pre inflation pressure, the equipment can directly inflate into the equipment through the one-way valve, so the inflation time can be saved.
4、安装储气罐。
4. Install the air receiver.
考虑到工况的不同，设备的输出高压力可预先储存到高压气罐中（气罐的容积大小请咨询技术工程师），根据用气设备的使用压力要求，使用减压阀来调节出口压力。
Considering the different working conditions, the high output pressure of the equipment can be stored in the high-pressure gas tank in advance (please consult the technical engineer for the volume of the gas tank). According to the operating pressure requirements of the gas equipment, the pressure reducing valve is used to adjust the outlet pressure.
5、气体增压泵入口侧压缩空气流量约为气体增压泵出口侧流量的2倍（增压设备的预增气体通过增压，中间会产生损耗）。
5. The compressed air flow at the inlet side of the gas booster pump is about twice the flow at the outlet side of the gas booster pump (the pre increased gas of the booster device will be lost in the middle through pressurization).
6、气体增压泵的寿命是由动作的频率决定。
6. The service life of the gas booster pump is determined by the action frequency.
此外，在气体增压泵再进行维护的时候，一定要在没有气压情况下进行维护，关闭驱动、关闭进气压力，卸荷高压输出压力再进行维护保养。另外建议与相关技术人员进行沟通或者视频指导下进行维护。
In addition, when the gas booster pump is maintained again, it must be maintained without air pressure. Turn off the drive, turn off the inlet pressure, and unload the high-pressure output pressure. In addition, it is recommended to communicate with relevant technicians or conduct maintenance under video guidance.
If the equipment needs to operate for a long time, please explain in the working conditions. The type of gas booster pump will be discussed and determined by the technical meeting, which will greatly boost the service life of the gas booster equipment. Come to our website for more information http://www.sdjingtuo.com Ask and understand!
