气体增压泵又叫空气增压泵，在流体控制行业内应用十分的广泛，高压气体增压泵可以将普通气体压力增压上百倍达到高压气体，以达到工作目的。下面来讲讲安装高压气体增压泵的六大步骤：
The gas booster pump, also known as the air booster pump, is widely used in the fluid control industry. The high-pressure gas booster pump can boost the pressure of ordinary gas up to 100 times to reach the high-pressure gas to achieve the working purpose. Here are the six steps to install the high-pressure gas booster pump:
1.高压气体增压泵的安装
1. Installation of high-pressure gas booster pump
空气增压阀标配有两个开槽安装支架，增压阀可以安装在任意位置，位置为垂直方向，每台售出增压阀都会附带图纸，标注所需的各种尺寸。
The air booster valve is equipped with two slotted mounting brackets as standard. The booster valve can be installed at any position. The recommended position is vertical. Each booster valve sold will be attached with drawings and marked with the required dimensions.
2.预增气源连接
2. Pre-increasing gas source connection
高压气体增压泵泵体上都标注进口，且图纸上都标有端口尺寸及型号。预增气体一定要纯净，气体介质若有杂志可能会损坏高压元件，导致增压阀运行故障，所以建议大家在增压阀进气口安装过滤装置。
The high-pressure gas booster pump body is marked with inlet, and the drawing is marked with port size and model. The pre-added gas must be pure. If the gas medium has a magazine, it may damage the high-pressure components and cause the operation failure of the booster valve. Therefore, it is recommended that you install a filter device at the inlet of the booster valve.
3.气源的连接
3. Connection of air source
供气回路的安装时过滤/调压阀需尽量开进增压阀。进气口端口为G1/阀体上标注为驱动气口管径为1/2，如果管径较小，增压阀就不可以以大流量运行。过滤调压需按照名称顺序链接，靠近增压阀。
When installing the air supply circuit, the filter/pressure regulating valve should be opened into the booster valve as much as possible. The air inlet port is G1/the pipe diameter of the drive air port is marked on the valve body as 1/2. If the pipe diameter is small, the booster valve cannot operate with large flow. Filter pressure regulation shall be linked in the order of name, close to the booster valve.
4.消声器
4. Muffler
消声器的使用时用来降低增压阀运行时的噪音，保证运行环境的安静。排气口端口为G1/2，标记为出气口。
The muffler is used to reduce the noise of the booster valve during operation and ensure the quiet operation environment. The exhaust port is G1/2, marked as the air outlet.
5.高压气体出口的连接
5. Connection of high-pressure gas outlet
在增压阀的配图上标有端口尺寸及型号，增压阀阀体上标注为“出口，此为高压出口，所以连接时需要特别谨慎小心，连接件需要大于大输出压力。
The port size and model are marked on the diagram of the booster valve, and the valve body of the booster valve is marked with“ Outlet, this is a high-pressure outlet, so special care should be taken when connecting. The connecting piece should be greater than the large output pressure.
6.高压气体增压泵的启动
6. Startup of high-pressure gas booster pump
⑴在打开增压阀的进气开关之前，使用调节减压阀将气压调到⑵确保所有的连接口及所有元件及安装。
(1) Before opening the air inlet switch of the booster valve, use the pressure reducing valve to adjust the air pressure to (2) Ensure that all connections and all components are installed.
⑶将减压阀缓慢调节增压阀开始启动，正常情况下增压阀在15-20PSI压力下气动。
(3) Slowly adjust the pressure reducing valve until the pressure boosting valve starts to start. Under normal conditions, the pressure boosting valve is pneumatically operated at 15-20PSI pressure.
⑷完成1到3步骤后，调节泵的供气气压直达到系统所需输出压力为止。
⑷ After completing steps 1 to 3, adjust the air supply pressure of the pump until it reaches the output pressure required by the system.
The above is about the gas booster pump. I hope it can help you. Come to our website for more use of relevant equipment http://www.sdjingtuo.com Consult!
