热线电话
0531-69951198
网站首页
关于精拓
产品展厅
新闻中心
原理选型
客户案例
在线留言
联系我们
网站公告:

新闻中心

济南精拓流体设备有限公司

电话:0531-69951198

邮箱:jingtuolt@163.com

传真:0531-69951198

地址:济南市历城区祝甸北路2号院

网址:http://www.sdjingtuo.com

常见问题

当前位置:首页 - 新闻中心 - 常见问题气液增压泵的使用可以了解

气液增压泵的使用可以了解这些

发布时间:2022-11-21 20:27:25   发布人:http://www.sdjingtuo.com
原则上,气液增压泵能够安装在大部分的位置,但为保证密封件达到长使用寿命,建议采用垂直安装方式。此外请确认所安装的接头和管是否在泵的压力范围内。
In principle, the gas-liquid booster pump can be installed in most positions, but in order to ensure the long service life of the seals, it is recommended to adopt the vertical installation method. In addition, please confirm whether the installed joints and pipes are within the pressure range of the pump.
驱动空气接口位于滑阀室外部。在任何情况下,都需要安装一个压缩空气过滤器和水分离器,
The drive air interface is located outside the spool valve chamber. In any case, a compressed air filter and water separator shall be installed,
因为液泵经过油脂润滑处理,所以无需安装空气润滑器。如使用过一次空气润滑器,则继续使用。如使用干燥的气体,则需使用气体润滑器。
Since the liquid pump is lubricated with grease, it is unnecessary to install an air lubricator. If the primary air lubricator has been used, it is recommended to continue to use it. If dry gas is used, a gas lubricator is required.
气液增压泵的驱动空气设计压力范围:PL=1-10bar(14.5-145psi)。
Design pressure range of driving air for gas-liquid booster pump: PL=1-10bar (14.5-145psi).
颗粒:大颗粒5μ;大颗粒浓度5mg/m3
Particles: large particles 5 μ; Large particle concentration 5mg/m3
露点:+10°=含水量9.4g/m3+2°C=含水量5.6g/m3
Dew point:+10 °=water content 9.4g/m3+2 ° C=water content 5.6g/m3
气液增压泵
含油量:1.0-5mg/m3
Oil content: 1.0-5mg/m3
注意:当使用湿气或高湿度气体连续操作时,会产生结冰现象,建议在此种情况下载空去驱动管线上安装一个水分离器或干燥器。
Note: When using wet gas or high humidity gas for continuous operation, icing will occur. It is recommended to install a water separator or dryer on the drive pipeline of the air separator in this case.
如果驱动空气过于干燥且露点低于-40°C,建议使用油雾器。
If the driving air is too dry and the dew point is below - 40 ° C, an oil mist atomizer is recommended.
标准温度范围为-20℃到+80℃。短时操作时,大操作温度可以达到+80℃。如在室外温度为0℃或低于0℃的情况下使用液泵,应采取防冻错施。
The standard temperature range is - 20 ℃ to+80 ℃. During short-term operation, the large operating temperature can reach+80 ℃. If the liquid pump is used when the outdoor temperature is 0 ℃ or lower than 0 ℃, anti freezing measures shall be taken.
泵的选型需考虑到客户的使用介质,因为介质的性质决定可密封材料和接液部件的要求。标准设计适用增压油或水。
The selection of pump shall take into account the medium used by the customer, because the nature of the medium determines the requirements for sealable materials and wetted parts. The standard design applies to pressurized oil or water.
泵的理论大输出压力为在驱动空气压力10bar时的输出压力。实际输出压力为驱动空气压力乘以压力比。流量为驱动空气压力PL=6bar,出口压力为0时液泵的近似流量。您如果要知道更多的事项就来我们网站http://www.sdjingtuo.com咨询吧!
The theoretical large output pressure of the pump is the output pressure when the driving air pressure is 10bar. The actual output pressure is the drive air pressure multiplied by the pressure ratio. The flow is the approximate flow of the liquid pump when the driving air pressure PL=6bar and the outlet pressure is 0. If you want to know more, please come to our website http://www.sdjingtuo.com Consult!
新闻: