气体增压泵是给气体增压的一种，其原理是利用低压气体推动大活塞来带动高压增压缸的小活塞，通过计算大小活塞的面积比来得到气体增压泵的增压比。下面来讲讲气体增压泵的使用六点注意事项，具体如下：
The gas booster pump is a kind of gas booster pump. Its principle is to use low pressure gas to drive the large piston to drive the small piston of the high pressure booster cylinder. The pressurization ratio of the gas booster pump is obtained by calculating the area ratio of the large and small pistons. Here are six precautions for the use of the gas booster pump, as follows:
1.使用方要准备好被增压的气体和管路，驱动气体和管路，高压气体的出口管路，按增压泵出厂时所带的说明先固定好增压泵，按照增压泵的各个进出口接头尺寸，连接好管路；检查是否耐压足够，接头是否有泄露等，检查完好后就可以进行增压测试了。
1. The user shall prepare the pressurized gas and pipeline, driving gas and pipeline, and outlet pipeline of high-pressure gas, fix the booster pump according to the instructions of the booster pump when it leaves the factory, and connect the pipeline according to the size of each inlet and outlet connector of the booster pump; Check whether the pressure resistance is sufficient and whether the connector has leakage. After the check is complete, the pressurization test can be carried out.
2.气源方面：气体增压泵的驱动气源压力范围一般是在1.8-8bar，不建议它的驱动气源超过10bar，如果驱动气源过高，那么很大程度上会对泵体造成损伤，更有甚者会对操作人员造成伤害。
2. Air source: The driving air source pressure range of the gas booster pump is generally 1.8-8bar. It is not recommended that its driving air source exceed 10bar. If the driving air source is too high, the pump body will be damaged to a large extent, and even the operators will be injured.
3.选型方面：客户要根据自身需求的压力选择对应的增压比，按照客户自己的压力需求，突出气源压力、进气压力、输出压力需求、流量是多少，这样技术人员才能更准确的帮您选型。
3. Model selection: The customer should select the corresponding boost ratio according to the pressure of their own needs, and highlight the air source pressure, intake pressure, output pressure demand and flow according to their own pressure needs, so that the technicians can help you select the model more accurately.
4.对现场使用环境方面：现场使用环境一定要干净，不能有太大的粉尘颗粒，驱动气源及被增压介质水分不要含量太多，否则会大大降低泵的使用的寿命。
4. For the on-site use environment: the on-site use environment must be clean and free of too large dust particles. The driving air source and pressurized medium should not contain too much moisture, otherwise the service life of the pump will be greatly reduced.
5.对管路的要求：客户现场使用的时候一定要检测高压输出管道的密封严实性，采用的管道、阀门、压力表一定要大于气体增压泵输出的额定压力，大限度的保证人员的操作。
5. Requirements for pipelines: When using on site, the customer must check the tightness of the high-pressure output pipeline. The pipes, valves and pressure gauges used must be greater than the rated pressure output by the gas booster pump, so as to ensure the operation safety of personnel to a large extent.
6.对压力容器的要求：各部分承压件，特别是压力容器，要具有压力容器厂家生产的压力容器检查报告。
6. Requirements for pressure vessels: all pressure parts, especially pressure vessels, shall have inspection reports of pressure safety vessels produced by pressure safety vessel manufacturers.
In addition, the life of the gas booster pump is determined by the frequency of action. Therefore, if the equipment needs to operate for a long time, please explain in the working conditions, and technicians will discuss and decide the type of pump, which will greatly increase the service life of the supercharging equipment. More relevant content will come to our website http://www.sdjingtuo.com consulting service
