网站公告:

新闻中心

济南精拓流体设备有限公司

电话:0531-69951198

邮箱:jingtuolt@163.com

传真:0531-69951198

地址:济南市历城区西周南路9号

网址:http://www.sdjingtuo.com

常见问题

当前位置:首页 - 新闻中心 - 常见问题 - 增压泵在没有水的情况下不

增压泵在没有水的情况下不停止工作原因

发布时间:2022-07-18 19:32:00   发布人:http://www.sdjingtuo.com
如果您发现增压泵在没有水的情况下不停止工作,可能是以下原因造成的:
If you find that the booster pump does not stop working without water, it may be caused by the following reasons:
1、可能是停机压力值设置过高。如果停机压力设置过高,无论有无水,增压泵都无法达到设定压力,自然不停机。
1. The shutdown pressure may be set too high. If the shutdown pressure is set too high, no matter there is no water, the booster pump cannot reach the set pressure and will not shut down naturally.
解决方法:如果有指针压力表,先看电流不停止时指针压力指示的位置,记下压力值,然后检查对应的设定停止压力值(仅针对可以自己设置)。压力值),适当降低设定的停机压力值,然后重试。
Solution: if there is a pointer pressure gauge, first look at the position indicated by the pointer pressure when the current does not stop, write down the pressure value, and then check the corresponding set stop pressure value (only for self setting). Pressure value), reduce the set shutdown pressure value appropriately, and then try again.
气液增压泵
2、单向阀漏水。单向阀的作用是防止已经加压的水的压力倒流,造成压力下降。如果单向阀密封不好导致漏水,则无法达到设定的上限,泵也不会停止。
2. The check valve leaks. The function of one-way valve is to prevent the pressure backflow of pressurized water, resulting in pressure drop. If the one-way valve is not well sealed, resulting in water leakage, the set upper limit cannot be reached, and the pump will not stop.
解决方法:先将增压泵加压到一定值,记下该值,然后关闭增压泵电源,观察指针是否会下降,如果下降则表示漏水。如果没有压力表,只能停一会,然后打开水龙头,看看水压有没有明显下降。
Solution: first pressurize the booster pump to a certain value, write down the value, then turn off the power supply of the booster pump, and observe whether the pointer will fall. If it falls, it means water leakage. If there is no pressure gauge, you can only stop for a while, and then turn on the tap to see if the water pressure drops significantly.
3、其他水管有漏水现象。管网其他水点漏水也会导致压力持续下降,达不到设定的停机压力值。
3. Other water pipes are leaking. Water leakage at other water points in the pipe network will also cause the pressure to continue to drop and fail to reach the set shutdown pressure value.
解决方法:这种可能性不大,但还是要观察是否有泄漏。
Solution: This is unlikely, but it is still necessary to observe whether there is leakage.
4、增压泵的控制器或传感器坏了。如果经过以上3个步骤仍然无效,则可能是增压泵的控制器或传感器坏了。
4. The controller or sensor of the booster pump is broken. If the above three steps are still invalid, the controller or sensor of the booster pump may be broken.
解决方法:这种性比较强,一般不要在没有厂家指导的情况下轻易测试,有触电的危险。
Solution: this kind of specialty is relatively strong. Generally, it is not easy to test without the guidance of the manufacturer. There is a risk of electric shock.
另外,达到压力平衡后,泵自动停机,采用单气控不平衡配气阀,实现泵的自动往复运动。泵体气动部分采用铝合金制造。与液体接触的部件根据不同介质采用碳钢或不锈钢制造,泵的全套密封件均采用进口优质产品,从而保证了气液增压泵的性能。
In addition, when the pressure is balanced, the pump will stop automatically, and a single pneumatic unbalanced valve is used to realize the automatic reciprocating motion of the pump. The pneumatic part of the pump body is made of aluminum alloy. The parts in contact with liquid are made of carbon steel or stainless steel according to different media, and the full set of seals of the pump are imported high-quality products, so as to ensure the performance of the gas-liquid booster pump.
增压泵在没有水的情况下不停止工作原因便是这样了,如果您还有其他问题就来关注我们网站http://www.sdjingtuo.com吧!
The reason why the booster pump doesn't stop working without water is this. If you have other problems, please follow our website http://www.sdjingtuo.com Come on!
新闻推荐:
阀门试验台使用前后的检查与注意 2022-08-05
气液增压泵怎么保养及维修注意什么 2022-07-29
增压泵在没有水的情况下不停止工作原因 2022-07-18
增压泵使用长久后会出现故障的表现形式 2022-07-11
订购到满意的增压泵就要知道参数及其他 2022-07-04
关于气液增压泵的正确打开认识方式 2022-06-22
增压泵怎样安装?有什么安装常见问题? 2022-06-15
讲解增压泵产品九大特点 2022-06-08
气体增压泵要加一个气罐的原因 2022-05-30
选择气体泄漏检测仪时要了解实际情况 2022-05-27

13188935873

qq