网站公告:

新闻中心

济南精拓流体设备有限公司

电话:0531-69951198

邮箱:jingtuolt@163.com

传真:0531-69951198

地址:济南市历城区西周南路9号

网址:http://www.sdjingtuo.com

常见问题

当前位置:首页 - 新闻中心 - 常见问题 - 关于气液增压泵的正确打开

关于气液增压泵的正确打开认识方式

发布时间:2022-06-22 18:00:14   发布人:http://www.sdjingtuo.com
当驱动部分和输出液体部分之间的压力达到平衡时,气液增压泵会停止运行,不再消耗空气。当输出压力下降或空气驱动压力增加时,增压泵会自动启动运行,直到再次达到压力平衡后自动停止。此外大家还需知道的该增压泵更多相关内容。
When the pressure between the driving part and the output liquid part reaches equilibrium, the gas-liquid booster pump will stop running and no longer consume air. When the output pressure drops or the air drive pressure increases, the booster pump will automatically start and run until it reaches the pressure balance again. In addition, you need to know more about the booster pump.
气液增压泵特点
Characteristics of gas-liquid booster pump
1、维护简单:增压泵零件和密封件少,维护简单,成本低。
1. Simple maintenance: the booster pump has few parts and seals, simple maintenance and low cost.
2、性价比高:增压泵具有输出性能高、成本低的特点。
2. High cost performance: booster pump has the characteristics of high output performance and low cost.
3、可调性强:增压泵的输出压力和流量由驱动气体的调压阀调节。调整驱动气压,使气压管路增压泵的输出压力在预增压气压和大输出压力之间调整。
3. Strong adjustability: the output pressure and flow of booster pump are regulated by the pressure regulating valve of driving gas. Adjust the driving air pressure so that the output pressure of the booster pump of the air pressure pipeline is adjusted between the pre pressurized air pressure and the large output pressure.
4、输出压力高:可实现气动液体管道增压泵的高工作压力,可实现气动气体管道增压泵的高工作压力。
4. High output pressure: it can realize high working pressure of pneumatic liquid pipeline booster pump and high working pressure of pneumatic gas pipeline booster pump.
5、材质优良:增压泵高压部分采用硬质铝合金制造。高压柱塞由不锈钢制成。并采用双层密封。关键部位的材料可根据介质进行选择。
5. Excellent material: the high-pressure part of booster pump is made of hard aluminum alloy. The high pressure plunger is made of stainless steel. And adopt double-layer sealing. The materials of key parts can be selected according to the medium.
气液增压泵
气液增压泵的使用方法:
Usage of gas-liquid booster pump:
1、用户应准备好加压气体及管道、驱动气体及管道、高压气体的出口管道。先按照增压泵出厂时的说明书固定增压泵。检查进出口接头尺寸,连接管路,检查耐压是否足够,接头是否漏水等,检查无误后,即可进行增压试验。
1. The user shall prepare pressurized gas and pipeline, driving gas and pipeline, and outlet pipeline of high-pressure gas. First, fix the booster pump according to the factory instructions of the booster pump. Check the size of inlet and outlet joints, connecting pipelines, whether the pressure resistance is sufficient, whether the joints leak, etc. after the inspection is correct, the pressurization test can be carried out.
2、气源:气液增压泵的驱动气源一般在1.8-8bar的压力范围内。不建议其驱动气源超过10bar。如果驱动气源过高,会对泵体产生很大影响。造成损害,甚至给操作者造成更多的伤亡
2. Air source: the driving air source of the gas-liquid booster pump is generally within the pressure range of 1.8-8bar. It is not recommended that the driving air source exceed 10bar. If the driving air source is too high, it will have a great impact on the pump body. Cause damage and even more casualties to operators
3、在气液增压泵选型方面:客户应根据自己的压力,根据自己的压力要求,选择相应的增压比,关注气源压力、进气压力、输出压力需求、流量、销量工程师可以帮助您更准确地选择
3. In terms of selection of gas-liquid booster pump: customers should select the corresponding boost ratio according to their own pressure and pressure requirements, focusing on air source pressure, inlet pressure, output pressure demand, flow and sales volume. Engineers can help you select more accurately
4、现场使用环境:现场使用环境必须清洁,无过多灰尘颗粒,驱动气源和加压介质中不应含有过多水分,会大大降低使用寿命。
4. Site service environment: the site service environment must be clean and free of excessive dust particles. The driving air source and pressurized medium should not contain too much moisture, which will greatly reduce the service life.
5、管道要求:客户在现场使用时必须检查高压输出管道的密封性。使用的管路、阀门和压力表必须大于气液增压泵输出的额定压力。
5. Pipeline requirements: the customer must check the tightness of the high-pressure output pipeline when using it on site. The pipeline, valve and pressure gauge used must be greater than the rated output pressure of the gas-liquid booster pump.
6、对压力容器的要求:所有承压部件,特别是压力容器,必须有压力安全容器生产企业出具的压力安全容器检验报告。
6. Requirements for pressure vessels: all pressure containing parts, especially pressure vessels, must have pressure safety vessel inspection reports issued by pressure safety vessel manufacturers.
以上就是今天为大家分享的关于问题的相关内容,希望对大家能有所帮助,想要了解更多内容可以电话联系我们或者关注我们的网站http://www.sdjingtuo.com
The above is the relevant content about the problem shared for you today. I hope it can help you. If you want to know more, you can contact us by phone or follow our website http://www.sdjingtuo.com 。
新闻推荐:
关于气液增压泵的正确打开认识方式 2022-06-22
增压泵怎样安装?有什么安装常见问题? 2022-06-15
讲解增压泵产品九大特点 2022-06-08
气体增压泵要加一个气罐的原因 2022-05-30
选择气体泄漏检测仪时要了解实际情况 2022-05-27
气体增压泵和气液增压泵两种设备可不能... 2022-05-23
气体增压系统典型应用的相关内容 2022-05-18
气液增压泵发展快的缘由是本身性能强 2022-05-11
气体增压泵设计选择方面有要了解的吗? 2022-05-04
气体增压泵压力稳定性怎么样? 2022-04-25

13188935873

qq