网站公告:

新闻中心

济南精拓流体设备有限公司

电话:0531-69951198

邮箱:jingtuolt@163.com

传真:0531-69951198

地址:济南市历城区西周南路9号

网址:http://www.sdjingtuo.com

常见问题

当前位置:首页 - 新闻中心 - 常见问题 - 气液增压机的上模安装要注

气液增压机的上模安装要注意什么?

发布时间:2021-11-10 16:56:46   发布人:http://www.sdjingtuo.com
上模固定板的双T形槽成60°,用模柄插入卡头安装,或采用压板或螺栓固定上模。具体分为以下类型:
The double T-shaped groove of the upper die fixing plate is 60 & deg;, Insert the die handle into the clamp for installation, or fix the upper die with pressing plate or bolt. It can be divided into the following types:
主轴带卡头安装,不防转,无总行程调节机构:
The spindle is installed with a chuck, without anti rotation and no total stroke adjustment mechanism:
此类结构主要用于压头重量较轻(3KG以下)且无需防转功能,无需总行程调节的情况。
This kind of structure is mainly used when the weight of the indenter is light (below 3kg) and there is no need for anti rotation function and total stroke adjustment.
主轴带卡头,双导柱防转机构,无总行程调节机构:
The main shaft is equipped with chuck, double guide post anti rotation mechanism, and there is no total stroke adjustment mechanism:
此类结构主要用于压头重量较轻(3KG以下)且需要防转功能,但无需总行程调节功能的情况。
This kind of structure is mainly used when the weight of the indenter is light (below 3kg) and the anti rotation function is required, but the total stroke adjustment function is not required.
气液增压泵
主轴带卡头,双导柱防转机构及总行程调节机构:
The main shaft is equipped with chuck, double guide post anti rotation mechanism and total stroke adjustment mechanism:
此类结构主要用于压头重量较重(3KG以上),采用卡头和模柄安装的情况。
This kind of structure is mainly used when the weight of the indenter is heavy (more than 3kg) and the clamp head and die handle are used for installation.
无卡头带上模板,双导柱防转机构及总行程调节机构:
No card head, with upper formwork, double guide post anti rotation mechanism and total stroke adjustment mechanism:
此类结构主要用于上模板安装,对导向精度和刚性的要求相对较低的情况。
This kind of structure is mainly used for the installation of upper formwork, and the requirements for guiding accuracy and rigidity are relatively low.
无卡头带上模板,四导柱防转机构及总行程调节机构:
No card head, with upper formwork, four guide pillar anti rotation mechanism and total stroke adjustment mechanism:
此类结构主要用于上模板安装,对导向精度和刚性的要求相对较高的情况。
This kind of structure is mainly used for the installation of upper formwork and has relatively high requirements for guiding accuracy and rigidity.
新闻推荐:
气体增压泵空气增压泵可以使用多长时间? 2021-11-30
气液增压泵施工步骤是先怎么操作? 2021-11-18
气液增压机的上模安装要注意什么? 2021-11-10
气体增压泵与气液增压泵的区别! 2021-10-20
为什么气体增压泵经常突然不工作了? 2021-10-13
气体增压设备一般的组成部分是? 2021-10-06
冬季来临,气动增压泵容易出那些问题? 2021-09-27
想要降低气动空气增压泵系统的温度能采... 2021-09-17
气体增压泵与气液增压泵的区别 2021-09-10
气动气体增压稳压设备的乱象,“怎么破”? 2021-09-06

13188935873

qq