关于气液增压泵在操作使用时有很多意事项，接下来，小编就为大家详细说一说，让大家了解关于气液增压泵的使用注意事项，让您的“泵”更好地为您服务！
There are many things about the operation and use of the gas-liquid booster pump. Next, I will tell you in detail, let you know the precautions about the use of the gas-liquid booster pump, and let your "pump" better serve you!
1、调节驱动压缩空气气源压力要求不大于0.8MPa（8kgf/cm?）。
1. Adjust the pressure of driving compressed air source to be no more than 0.8MPa (8kgf / cm?).
2、接通被增压空气管路，被增压空气进气压力范围为1.5bar-16bar，接通管路后，可观察被增压介质空气压力表的数值，保证驱动气路系统的清洁和正常工作条件。
2. Connect the pressurized air pipeline, and the pressure range of the pressurized air intake is 1.5bar-16bar. After connecting the pipeline, observe the value of the air pressure gauge of the pressurized medium to ensure the cleanness and normal working conditions of the drive air system.
3、当被增压空气压力达到所设定压力，即空气气瓶被充满时，两边压力达到平衡状态，增压泵停止工作，这时可关闭压缩驱动气源，关闭两边空气气瓶，此时，打开高压开关，进行增压系统管路泄气，以便高压气体排出。排完后，则立即关死高压卸荷球阀，可进行下一次充气。
3. When the pressure of the pressurized air reaches the set pressure, i.e. when the air cylinder is full, the pressure on both sides reaches the equilibrium state, and the booster pump stops working, then the compressed driving air source can be closed, and the air cylinders on both sides can be closed. At this time, the high-pressure switch can be turned on, and the pipeline of the booster system can be vented, so that the high-pressure gas can be discharged. After discharging, the high-pressure unloading ball valve shall be closed immediately for the next inflation.
4、紧固好空气增压系统及各连接管接头，防止因振动撞击擦产生静电火花。使用抗静电软管。
4. Fasten the air booster system and all connecting pipe joints to prevent electrostatic sparks caused by vibration impact. Use antistatic hose.
5、保持良好的排气和通风、远离易燃易爆和热源。
5. Keep good exhaust and ventilation, away from inflammable, explosive and heat source.
6、泵的排气中可能含有固体物，不要将排气口对着工作区或者人，以免造成人身伤害。
6. The exhaust of the pump may contain solids. Do not face the exhaust port to the work area or people, so as to avoid personal injury.
7、当输送易燃和有毒的流体时，请将排口接到远离工作区的地方。
7. When transporting flammable and toxic fluid, please connect the drain to a safe place away from the work area.
8、流体的高压可能会导致严重的人身伤亡和财产损失，请不要在泵加压时，对泵及料管系统进行任何的维修工作，如要做维修时，先切断泵的进气，慢慢松开连接的各管道接头。
8. The high pressure of the fluid may cause serious personal injury and property loss. Please do not carry out any maintenance work on the pump and the material pipe system when the pump is pressurized. If the maintenance is to be done, cut off the air inlet of the pump first, and slowly loosen the connected pipe joints.
9、为了保证泵的寿命，建议驱动气压≤8bar此系列的驱动活塞直径为160mm。
9. In order to ensure the service life of the pump, it is recommended that the diameter of the driving piston of this series with the driving air pressure ≤ 8bar be 160mm.
10、保证所有接触输送体的部件不会被输送的流体腐蚀损坏，并且要保证所有的操作人员熟悉操作使用和掌握泵的使用注意事项，必要的话，配给必需的防护用品。
10. Ensure that all parts contacting the conveying body will not be corroded and damaged by the conveying fluid, and ensure that all operators are familiar with the operation and use and master the precautions for safe use of the pump, and allocate necessary protective equipment if necessary.
The above is the relevant content introduced by the gas booster pump manufacturer. For more information, please visit the website: http://www.sdjingtuo.com
