1.实验台的台面平坦、润滑,需求边际切开规整,四边平直,无显着凹凸表象.贴面和封边部件紧密、平坦,不允许有脱胶、鼓泡、洼陷、压痕、外表划伤、麻点、裂缝、崩角和刀口等
1. the platform is flat and lubricated, the demand margin is cut and neat, the four sides are straight, and there is no obvious concave and convex representation. The face and edge parts are close and flat, and no degumming, bubbling, depression, indentation, scratches, scratches, cracks, avalanche and knife edges are not allowed.
2.各涂层均匀,钢制或木制板外表平坦,五色差、无拼接、无显着凹凸、驳、无划痕、无碰伤等残损.切开、钻孔和倒角无毛刺,外表的圆角、倒棱均匀共同
2. uniform coating, steel or wooden board flat surface, five colors, no splice, no obvious concave and convex, no mottled, no scratches, no scratches and other damage. Open, boring and chamfering no burr, the appearance of the round angle, even common chamfering joint.
3.柜体的每一块,其四个边有必要用热熔胶经高温高压作防水封边处置
3. each part of the cabinet must be treated with high quality hot-melt adhesive at high temperature and high pressure.
4.柜体的板块与板块之间的衔接,选用三合一内预埋衔接件,在放置三合一衔接件的"L"形孔洞的两头有必要注满黄胶,以增强握钉力,抗弯弧变形、防渗水、防摇晃.并一起运用滚花木质圆棒棰,带胶安稳加固衔接
4. the link between the plate and the plate of the 4. cabinet is selected with a high quality three in one inside. The two ends of the "L" shaped hole in the connecting part are filled with yellow glue to strengthen the grip strength, bend the arc deformation, prevent seepage and shake off.
5.柜体的板块与五金配件之间的衔接,在巩固一切螺钉之前,有必要打一个小于螺钉直径和长度的孔,高压写入胶水后,再行拧入螺钉,以增强握钉力,如为螺钉与螺母衔接可在外
5. the connection between the plate and the hardware fittings. Before consolidating all the screws, it is necessary to make a hole smaller than the diameter and length of the screw. After the high pressure is written to the glue, the screw is twisted into the screw so as to enhance the grip strength, such as connecting the screw and the nut to the outside.
6.一切柜体衔接结实,无松动表象;外表平坦无显着变形;显露有些无毛刺及尖利锋芒
6. all cabinets are connected and strong, without loose appearance; flat appearance without significant deformation; showing some burrs and sharp edges.
7.零部件无开裂或劈裂表象,不会呈现影响运用功用的磨损变形表象,可动有些(例如可调式地脚、活动隔板等)活动灵活,用手掀压不会呈现永世形变形或松动,抗压才能契合实验台的需求
7. parts have no cracking or split appearance, and will not present the wear and deformation representation that affects the use of the function. It can move some (such as adjustable feet, movable baffles, etc.) flexibly, and the hand lift will not present the everlasting deformation or loosening, and the pressure can fit the demand of the experimental platform.
8.单相三线电源插座与两线插头相兼容
8. single-phase three wire sockets are compatible with two wire plugs
9.一切水、电、气路需求、适用,并隐藏式装置
9. all water, electricity and gas roads are safe, applicable and hidden.
10.产物尺度需求:长、宽、高差错点≤3mm;邻边笔直度:台面对角线、结构对角线1000mm≤3mm; 2000mm≤4mm; 3000mm≤
10. product scale requirements: length, width, height difference error point is less than 3mm; adjacent edge straightness: table diagonal, structural diagonal 1000mm less than 3mm; 2000mm = 4mm; 3000mm less than
On the gas booster pump http://www.sdjingtuo.com first introduced here, I believe you will use the relevant knowledge in the actual work, if you have the needs of this area, welcome to buy.
