气液增压泵总会有存放的，那么这个时候就应该做好相应的预防以及准备措施了，不要短期放置或者长时间放置导致设备的故障。下面来讲讲存放的要求。
The gas-liquid booster pump will always be stored for one day. At this time, corresponding preventive and safety measures should be taken. Do not place it for a short time or a long time to cause equipment failure. Let's talk about storage requirements.
总体要求
General requirements
存放之前，检查每个气液增压泵有否损坏。万一在运输过程中发生损坏现象，应对损坏程度进行严格评估，做好记录并立即以书面的形式告知供应商（以获取相关储存建议）。
Before storage, check whether each gas-liquid booster pump is damaged. In case of damage during transportation, the extent of damage shall be strictly evaluated, recorded and immediately notified to the supplier in writing (to obtain relevant storage suggestions).
存放之前，应进行开箱验收工作-仔细核查所供产品及备件的规格（尺寸）、材料等是否与清单一致？是否有损伤的迹象？
Before storage, unpacking acceptance shall be carried out - carefully check whether the specifications (dimensions), materials, etc. of the products and spare parts supplied are consistent with the list? Is there any sign of damage?
所有提供的零部件应存储在空气湿度尽可能恒定的、干燥的房间内。
All parts provided shall be stored in a dry room with the air humidity as constant as possible.
如果在室外存储，必须覆盖泵组和板条箱以形成防水屏障，保护它们饱受水珠进入，从而避免与湿气的任何接触。
If stored outdoors, the pump unit and Flat noodles must be covered to form a waterproof barrier to protect them from water droplets, thus avoiding any contact with moisture.
短期或长期储存
Short-term or long-term storage
气液增压泵泵组和备件储存时间的长短会影响其储存方式。如果你不知道备件将被储存多长时间，请保守一点。
The storage time of gas-liquid booster pump unit and spare parts will affect its storage mode. If you don't know how long the spare parts will be stored, please be conservative.
无论储存期如何，正确的程序和良好的记录都关重要。环境控制少应包括温度、湿度、空气污染和减轻振动。
Regardless of the storage period, correct procedures and good records are essential. Environmental control shall at least include temperature, humidity, air pollution and vibration reduction.
未安装的备用轴承应保存在原始设备制造商的包装中，并平置存放。密封（脂润滑）轴承的存放时间不得超过五年。非滚动轴承可能会出现自身的一系列储存问题，因此请务必咨询泵制造商。
Spare bearings not installed shall be kept in the original equipment manufacturer's packaging and stored horizontally. The storage time of sealed (grease lubricated) bearings shall not exceed five years. Non-rolling bearings may have a series of storage problems of their own, so please consult the pump manufacturer.
旧泵与新泵的储存有所不同。使用过的泵或零件的大问题是，在开始储存程序之前，通常需要完全泵送产品。许多人忽视了这一步，或采取了50%的行动，却使泵100%无法使用。
The storage of old pump is different from that of new pump. The big problem with used pumps or parts is that it is usually necessary to completely remove the pumped product before starting the storage procedure. Many people ignore this step or take 50% action, but make the pump 100% unusable.
用过的泵是存放在适当的地方还是存放在安装区域？在大多数情况下，需要泵送产品，并用防腐油喷涂或雾化流道金属表面。同时，涂覆所有暴露的机加工表面。
Is the used pump stored in a proper place or in the installation area? In most cases, it is necessary to remove the pumped product and spray or atomize the metal surface of the flow passage with anti-corrosion oil. At the same time, coat all exposed machined surfaces.
备件等存放地点和方式是需要考虑的重要因素之一。在理想情况下，储存空间应在室内，且其中的温度和湿度保持相对恒定（湿度好保持在50%以下，温度低于35℃）。温度波动应限制在10℃以下，尤其是在湿度控制不好的情况下。恒定的温度和湿度对于成功储存关重要，因为它可以减少会导致腐蚀的冷凝。
The storage location and method of spare parts are one of the important factors to be considered. Ideally, the storage space should be indoor, and the temperature and humidity in it should be relatively constant (the humidity should be kept below 50%, and the temperature should be below 35 ℃). Temperature fluctuation shall be limited to below 10 ℃, especially in case of poor humidity control. Constant temperature and humidity are critical for successful storage because they reduce condensation that can lead to corrosion.
Some long-term storage procedures require the rotor to be placed in a sealed box, or the pump body to be sealed at the flange and penetration. Use a vacuum pump to extract air and then fill it with inert gas (usually nitrogen). Come to our website for more relevant content http://www.sdjingtuo.com Ask!
