小型气动增压泵参数：
Parameters of small pneumatic booster pump:
增压介质：各种无腐蚀性洁净气体。
Pressurization medium: various non corrosive clean gases.
更高增压压力：80MPA。
Higher boost pressure: 80MPa.
单台更大流量:1200L/min(也可多台并联流量更大)。
Larger flow of single set: 1200L / min (more flow of multiple sets can also be connected in parallel).
单台更大耗气量：900L/min。
Larger gas consumption per unit: 900l / min.
驱动压力要求：2-8bar(6-8bar更佳驱动)。
Driving pressure requirements: 2-8bar (6-8bar is better).
小型气体增压泵得结构和原料：
Structure and raw materials of small gas booster pump:
小型气体增压泵总体分为增压部分，驱动部分和操控部分。增压部分部件大致有，前后增压端盖铸钢，双层增压缸缸筒内304外铸钢，1套单向阀有密封垫.绷簧.钢珠.单向阀表里壳体等组成，U型冷却管铝合金，增压活塞和活塞杆密封圈等一系列组成增压部分。驱动部分大致有，前后端盖铸钢，驱动缸筒铝合金，前后撞针304钢材和密封圈(功用铺助操控部分换向)，高低压换气钢管304原料，驱动活塞和活塞杆密封圈等一系列组成驱动部分。操控部分大致有驱动腔体铸钢，换向阀分为外阀套和内阀芯有铝合金和密封圈组成。
The small gas booster pump is generally divided into booster part, driving part and control part. The pressurization parts are generally made of steel, front and rear pressurization end covers, 304 outer steel in the cylinder barrel of double-layer pressurization cylinder, and a set of one-way valve is provided with sealing gasket Tension spring Steel ball The check valve is composed of the inner and outer shell, U-shaped cooling pipe, aluminum alloy, booster piston and piston rod sealing ring. The driving part consists of a series of driving parts, such as front and rear end cover cast steel, driving cylinder barrel aluminum alloy, front and rear striker 304 steel and sealing ring (function shop helps the reversing of the control part), high and low pressure air exchange steel pipe 304 raw materials, driving piston and piston rod sealing ring, etc. The control part is roughly composed of driving cavity cast steel. The directional valve is divided into outer valve sleeve and inner valve core, which is composed of aluminum alloy and sealing ring.
订购需要注意什么：
What to pay attention to when ordering:
1、驱动气体的压力和流量
1. Pressure and flow of driving gas
一切的泵和动力单元在接连作业时运用的驱动气压不超过0.69Mpa，在间歇作业时可达到1.03Mpa。在理想功能状况时气动泵的耗气量，请参照所需驱动气体流量表。
The driving air pressure used by all pumps and power units during continuous operation shall not exceed 0.69mpa and can reach 1.03mpa during intermittent operation. For the air consumption of the pneumatic pump under the ideal functional condition, please refer to the required driving gas flow table.
2、作业压力和流量
2. Operating pressure and flow
一切的泵和动力单元的作业压力参照驱动气压为0.48Mpa时泵输出压力和流量。假如泵的更大输出压力大于所需的作业压力，这就要考虑措施。对于更大输出压力，请参照产品目录中的“静态下驱动气压力和输出液压近似比率表”。动力单元的选型与泵一致。
The operating pressure of all pumps and power units refers to the pump output pressure and flow when the driving air pressure is 0.48mpa. If the greater output pressure of the pump is greater than the required working pressure, safety measures should be considered. For larger output pressure, please refer to the "table of approximate ratio between static driving air pressure and output hydraulic pressure" in the product catalog. The selection of power unit is consistent with that of pump.
3、运送液体介质
3. Transport liquid medium
泵运送的液体介质是泵的选型中着重考虑的部分。液压部分的原料和液压密封圈是由运送的液体介质所决定的。泵可用油、水和大多数液体介质。标准泵的首要液压密封圈是丁橡胶和聚氨酯，单向阀座选用特氟龙密封。其它密封材料包括碳氟化合物和亚乙基丙烯，这些密封材料首要用于运送的特别介质。请向工厂或当地的分销商咨询密封材料选型。
The liquid medium transported by the pump is an important part to be considered in the selection of the pump. The raw materials and hydraulic sealing rings of the hydraulic part are determined by the transported liquid medium. The pump can use oil, water and most liquid media. The primary hydraulic sealing ring of the standard pump is butadiene rubber and polyurethane, and the one-way valve seat is sealed with Teflon. Other sealing materials include fluorocarbons and ethylenepropylene. These sealing materials are mainly used for special media for transportation. Please consult the factory or local distributor for the selection of sealing materials.
4、可接受的体积和分量
4. Acceptable volume and weight
对于某些的应用，泵和动力单元的外形尺寸和分量也要考虑。
For some applications, the overall dimensions and components of pumps and power units should also be considered.
The gas-liquid booster pump has focused on the development of the industry for more than ten years, sincerely serving customers and focusing on customer needs. If you have unclear content, you can click the website to learn more: http://www.sdjingtuo.com
