热线电话
0531-69951198
网站首页
关于精拓
产品展厅
新闻中心
原理选型
客户案例
在线留言
联系我们
网站公告:

新闻中心

济南精拓流体设备有限公司

电话:0531-69951198

邮箱:jingtuolt@163.com

传真:0531-69951198

地址:济南市历城区祝甸北路2号院

网址:http://www.sdjingtuo.com

企业动态

当前位置:首页 - 新闻中心 - 企业动态订购气液增压泵您需要知道

订购气液增压泵您需要知道四个情况

发布时间:2022-10-21 13:49:37   发布人:http://www.sdjingtuo.com
要使您的气液增压泵处于很好的工作状态,订购气液增压泵要注意四个事项,下面小编为您整理下看看吧。
In order to keep your gas-liquid booster pump in good working condition, you should pay attention to four items when ordering the gas-liquid booster pump. The following sections will sort them out for you.
1.气液增压泵的驱动气体的压力和流量。
1. Pressure and flow of driving gas of gas-liquid booster pump.
在连续工作时,所有的气液增压泵和动力单元使用的驱动气压不超过0.69Mpa,在间歇工作时可达到1.03Mpa。
During continuous operation, the driving air pressure used by all gas-liquid booster pumps and power units shall not exceed 0.69 Mpa, and can reach 1.03 Mpa during intermittent operation.
2.气液增压泵的工作压力和流量。
2. Working pressure and flow of gas-liquid booster pump.
所有的气液增压泵和动力单元的工作压力参照驱动气压为0.48Mpa时泵输出压力和流量。如果泵的大输出压力大于所需的工作压力,这就要考虑做好措施以免发生意外。
The working pressure of all gas-liquid booster pumps and power units shall refer to the pump output pressure and flow when the driving air pressure is 0.48Mpa. If the large output pressure of the pump is greater than the required working pressure, safety measures should be taken to avoid accidents.
气液增压泵
3.气液增压泵的输送液体介质。
3. Delivery liquid medium of gas-liquid booster pump.
气液增压泵输送的液体介质是选型中着重考虑的部分。液压部分的材质和液压密封圈是由输送的液体介质所决定的。气液增压泵可用油、水和大多数液体介质。
The liquid medium delivered by the gas-liquid booster pump is a key part of the selection. The material of the hydraulic part and the hydraulic seal ring are determined by the liquid medium conveyed. The gas-liquid booster pump can use oil, water and most liquid media.
标准泵的主要液压密封圈是丁橡胶和聚氨酯,单向阀座采用特氟龙密封。其它密封材料包括碳氟化合物和亚乙基丙烯,这些密封材料主要用于输送的特殊介质。
The main hydraulic sealing rings of the standard pump are polybutadiene rubber and polyurethane, and the one-way valve seat is sealed with Teflon. Other sealing materials include fluorocarbon and ethylidene propylene, which are mainly used for special media.
4.气液增压泵的体积和重量。
4. Volume and weight of gas-liquid booster pump.
对于某些的应用,泵和动力单元的外形尺寸和重量也要考虑。
For some applications, the overall dimensions and weight of pumps and power units should also be considered.
以上就是问题的相关解答了,您对此有什么想法要分享的吗?可以随时来我们网站http://www.sdjingtuo.com进行咨询了解!
The above is the answer to the question. Do you have any ideas to share? You can come to our website anytime http://www.sdjingtuo.com Ask about it!
新闻: