热线电话
0531-69951198
网站首页
关于精拓
产品展厅
新闻中心
原理选型
客户案例
在线留言
联系我们
网站公告:

新闻中心

济南精拓流体设备有限公司

电话:0531-69951198

邮箱:jingtuolt@163.com

传真:0531-69951198

地址:济南市历城区祝甸北路2号院

网址:http://www.sdjingtuo.com

企业动态

当前位置:首页 - 新闻中心 - 企业动态使用企业增压缸我们应该注

使用企业增压缸我们应该注意什么?

发布时间:2020-10-29 16:47:36   发布人:http://www.sdjingtuo.com
1、保持清洁
1. Keep clean
在将增压缸接入气路前,敬请先将管路及元件内的灰尘等杂物,以免降低增压缸的使用寿命。
Before connecting the booster cylinder to the air circuit, please remove the dust and other impurities in the pipeline and components, so as to avoid reducing the service life of the booster cylinder.
2、正常气压范围内使用
2. Use within normal pressure range
缸在正常使用时工作气压必须要按照检验报告中规定的工作气压范围内工作,不得超过规定的工作压力.。
When the cylinder is in normal use, the working pressure must be within the working pressure range specified in the inspection report, and shall not exceed the specified working pressure.
3、注意增压缸的工作环境
3. Pay attention to the working environment of booster cylinder
缸在设工作环境内的温度已定,若因工作需要变换工作环境超过温度需与玖容增压缸技术相关人员联系处。
The temperature in the working environment of the cylinder has been determined during the design. If the working environment exceeds the temperature due to working needs, contact the technical personnel of the nine volume booster cylinder.
由于缸中的部分元件为铁质,所以请不要将其置于工况环境特为复杂的环境内使用(如有化学物质的接触环境),另请在缸前端加装有效的空气处理元件(三点组合)并接时加油润滑及排水处理。
As some components in the cylinder are made of iron, please do not use them in the environment with complicated working conditions (such as chemical contact environment). In addition, please install effective air treatment elements (three-point combination) at the front end of the cylinder, and then add lubrication and drainage treatment.
4、不可擅改加其它液压油
4. Do not add other hydraulic oil without authorization
增压缸在设所选用的液压油价质为VG68#抗磨液压油,不可撤擅自改用其它液体介质(如机油.水等)。
The quality of VG68 anti-wear hydraulic oil is selected in the design of booster cylinder, and it is not allowed to use other liquid medium (such as engine oil, water, etc.) without authorization.
5、一定要按程序操作
5. Be sure to follow the procedure
动作程序一定要按照气路配装图的动作程序工作即预压动作-增压动作增压释压-预压复位
The operation procedure must be in accordance with the operation procedure in the gas circuit assembly drawing, that is, pre pressure action - pressure increase action - pressure release - pre pressure reset
6、注意保养,经常检查增压缸运转
6. Pay attention to maintenance and check the operation of booster cylinder frequently
为避免缸在增压时动作的压力过大破坏您的模具或工件,敬请在增压段进入口处加装一减压阀,以便能有效保护您的产品。
In order to avoid damage to your mold or workpiece due to excessive pressure during cylinder pressurization, please install a pressure reducing valve at the inlet of pressurization section, so as to effectively protect your products.
气液增压泵
为确保增压缸工作的稳定性,建议尽可能在三联件与增压缸之间并联加装一储气筒。
In order to ensure the working stability of the booster cylinder, it is suggested to install an air reservoir in parallel between the triplet and the booster cylinder as far as possible.
使用增压缸500000次以上或半年以上时,建议将缸中的液压油全部更换一次,以提高缸的使用寿命和工作年限。
When the booster cylinder is used more than 500000 times or more than half a year, it is recommended to replace all the hydraulic oil in the cylinder once, so as to improve the service life and working life of the cylinder. 
新闻: