热线电话
0531-69951198
网站首页
关于精拓
产品展厅
新闻中心
原理选型
客户案例
在线留言
联系我们
网站公告:

新闻中心

济南精拓流体设备有限公司

电话:0531-69951198

邮箱:jingtuolt@163.com

传真:0531-69951198

地址:济南市历城区祝甸北路2号院

网址:http://www.sdjingtuo.com

企业动态

当前位置:首页 - 新闻中心 - 企业动态管道增压泵的工作原理

管道增压泵的工作原理

发布时间:2017-10-20 18:16:42   发布人:http://www.sdjingtuo.com
增压泵利用大面积活塞的低压气体(2—8bar)驱动而在小面积活塞上产生高压气体/液体。可用于压缩空气及其他气体,输出气压可通过驱动气压无级调节。 气体管道增压泵有单作用泵和双作用泵。双作用泵气活塞在往复两个冲程中都压缩气体。
High pressure gas / liquid is produced on a small area piston by driving a low pressure gas (2 - 8bar) of a large area piston. It can be used for compressed air and other gases, and the output air pressure can be stepless regulated by driving air pressure. The booster pump of gas pipeline has single acting pump and double acting pump. The double acting pump piston compresses the gas in two strokes of reciprocating stroke.

当驱动气体作用于气活塞时,工作活塞随气驱动就可获得较大的输出流量。增压泵具有以下特点:维护简单:增压泵的零件及密封少,维护简单且成本低着一起复增压。性价比高:增压泵具有输出性能高而成本低的特性。可调性强:增压泵输出压力和流量都由驱动气体的压力调节阀准确地调节。
When the driving gas acts on the gas piston, the working piston can obtain larger output flow with the gas driving. The booster pump has the following features: simple maintenance: parts and seals of the booster pump are less, the maintenance is simple and the cost is low. High cost performance: booster pump has high output performance and low cost characteristics. Adjustability: the output pressure and flow of the booster pump are regulated accurately by the pressure regulating valve of the driving gas.
调节驱动气压,使气压管道增压泵的输出压力在预增气压和较大输出压力之间精确调整。 输出压力高:气动液体管道增压泵的高工作压力可达到700Mpa,气动气体管道增压泵的高工作压力可达到300 Mpa。
Adjusting the driving pressure, the output pressure booster pump pressure pipeline precise adjustment between the pre pressure and maximum output pressure. The output pressure is high: the maximum working pressure of the pneumatic liquid pipe booster pump can reach 700Mpa, and the maximum working pressure of the pneumatic gas pipeline booster pump can reach 300 Mpa.
材质:增压泵高压部分材质为硬质铝合金。高压柱塞材质为不锈钢。并采用双层密封。关键部位材质可以根据介质性制选配。多种气体驱动:压缩空气、氮气、水蒸汽等。
High quality material: high pressure part of booster pump is made of hard aluminum alloy. High pressure plunger material is stainless steel. Double layer seal is adopted. The material of key parts can be chosen according to the dielectric property. A variety of gas driven: compressed air, nitrogen, steam and so on.
本文由气体增压泵友情奉献,更多有关的知识请点击:http://www.sdjingtuo.com我们将用的技术,真诚的态度,为您提供为的服务。我们将会陆续向大家奉献,敬请期待。
This article by gas booster pump friendship dedication, more relevant knowledge, please click: http://www.sdjingtuo.com, we will use the most advanced technology, the most sincere attitude, to provide you with the most comprehensive service. We will continue to dedicate to you, please look forward to.
新闻: